7 " Wide LCD Monitor
With 4 Mounting Options
PLHR7 1
AURM-1 0B
PLVHR7 2
INSTRUCTION MANUAL
www.pyleaudio.com
About the liquid crystal display (LCD) panel
1. Do not press on the LCD panel on the monitor unit as doing so can distort the picture or cause a
malfunction, the picture may become unclear, or the LCD panel may be damaged.
2. Notes on cleaning
-clean the LCD panel with a slightly damp soft cloth.
- do not use solvents such benzine, thinner, commercially available cleaners or antistatic spray.
3. Do not use this unit temperatures under 5oC (41oF) or over 45oC (113oF).
4. If your car was parked in a clod or hot place, the picture may not be clear. The monitor is not damaged.
The picture will become clear after temperature in your car becomes normal.
5.Some stationary blue or red dots may appear on the monitor.These are called bright spots, and happen
with anyLCD.The LCD panel is highly sophisticated, and more then 99.99% of the segments used in
the panel are flawless.However, there is a possibility that less than 0.01% of the segments are defective
and maynot light up properly. However, these segments will not interfere with your viewing.
Warning
To Prevent fire or shock hazard, do not expose the unit to
rain or moisture.
This symbol is intended to alert the user to
thepresence of uninsulated “DANGEROUS
VOLTAGE” within the product’s encloseure
that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
CAUTION!!
RISK OF ELECTRIC SHOCK
!
DO NOT OPEN
!
Caution: To reduce th risk of electric shock
This symbol is intended to alert the user to
Do not remove cover (or Back)
No user-serviceable parts inside
Refer servicing to qualified service personnel
the presence of important operating and
maintenance(servicing) instructions in the
literature accompanying the appliance.
Troubleshooting guide
The following checklist will help you solve problems you may encounter with your unit.
Before going through the checklist below, check the connection and operating.
if you can not solve the problem with follows guide, please contact your nearest dealer.
Problem
Cause/solution
The power cord or battery has been disconnected.
The fuse has blown.
No picture, no sound
Press power on.
Press the volume increase button on the wireless
remote, or on the monitor.
Press the mute button from the wireless remote.
(TIP: refer to page 4 for the “control & layout”)
Good picture, but no sound
Dolled lines or stripes
This maybe caused by local interference such as car
engine or motorcycle.
The cord has been disconnected. Connect the cord
securely.
Press power on.
No picture, or no sound when you
connect the optional equipment
No response when pressing the buttons on
the wireless remote
The wireless remote batteries may be exhausted.
2
Precautions
Please read this manual completely and carefully prior to attempt to install your new car video
equipment. Install correctly, your new equipment will provide you with years of enjoyable and safe usage.
Installing this unit requires technical expertise. This unit should be installed by a qualified
technician or service personnel. If you try to install this unit by yourself, do it properly, referring to the
installation and wiring diagrams in this operating manual. Improper installation may result in fire or
electric shock.
1.Do not operate this equipment while driving-safe driving should always be your highest priority.
2.Do not install components in areas which are susceptible to rain, moisture direct sunlight, extremely
heat or cold, excessive dust, dirt or humidity.
3. Immediately unplug the power cord and send the monitor to your local dealer or service center as
soon as possible:
a) If there is smoke or any peculiar odor present during used
b) If there is damage to any of the internal components
4. To avoid damage to the monitor and risk of electronic shock, do not permit any of this equipment to
become damp or wet from water or liquid. If this does occur, immediately unplug the power cord and
send the monitor to your local dealer or service center as soon as possible.
5. Do not attempt to repair, open or disassemble any of the components. Dangerous high voltages are
present which may result in electric shock.
6. Use only a power source with DC12 volts car battery (negative ground).
7. Do not place or suspend objects on the power cord, as this may damage the cord.
8. Do not twist or place the power cord near any source of heat in the vehicle.
9. Do not attempt to repair a damaged, broken or faulty power cord. Replace it with a new one immediately.
10. Avoid dropping any metal objects or inflammable items into the monitor ventilation slots.
11. After the monitor is installed, do not arbitrarily pull it down or strike it. This may loose the mounting
screws and cause it fall down.
12. Do not install this unit where:
a) it will obstruct the driver’s view.
b) it will obstruct the operation of the airbag system.
c) it will obstruct the operation of the vehicle, especially the steering wheel, shift lever, or brake pedal.
d) a diver or passengers may injure themselves when getting into or out of the car.
3
Control and layout for the monitor
Blue screen when
no video signal
Front Audio Output
Front audio output
Remote Sensor
Remote control IR sensor
(headphones)
Power On / Off
Front A/V Input
Turn on/off the monitor
Front audio video input
Menu
Press to display MENU
with functions and setting
Power Cord
(Male)
Adjust Increase
Adjust Decrease
This multipurpose button
serves to increase the selected
parameters, such as volume,
contrast etc.
This multipurpose button serves
to decrease the selected
parameters, such as volume,
contrast etc.
Notice: some functions are work by remote control.
Control and layout for the remote control
Mute
Power On/Off
Turn On / Off the monitor
Press to Mute the sound, press again
to restore the previous volume level
Volume Increase
Adjust increase headphone output
volume
Adjust Increase
This multipurpose button serves to
adjust down to select menu function
and increase the selected parameters
such as contrast, color, brightness etc
Adjust Decrease
This multipurpose button serves to
adjust up to select menu function
and decrease the selected parameters
such as contrast, color, brightness etc.
Volume Reduce
Adjust reduce headphone output
volume
Preset
Picture preset by factory
Menu
This button brings up the on-screen
menu for adjustment of a range of
monitor parameters such as,
V1/V2
Select Video 1 or Video 2 Input
vol, con, col, bri, tint. Etc
AURM-10B
Invert
To adjust the picture
up/down
When you use a wireless radio or portable telephone near
this unit, picture or sound interference may occur. Do not
use such devices near this unit.
4
Accessories
Universal Stand
Headrest &
Sun Visor Shroud
AURM-1
0
B
Remote Control
Headrest Case
Key-for removing the monitor
from headrest or visor shroud
Extension Min Din Cable
7 " Wide LCD Monitor
Mounting Options
With
3
P
LHR7
1
A
U
R
M
-
1
0
B
PLVHR7 2
INSTRUCTIO
N
MANUAL
w
w
w
.
pyleaudio
.co
m
Instruction Manual
5
Connection Diagram
1
2
Fuse
(2A)
Fuse replacement
Never use fuse with an amperage rating exceeding the one supplied
with the unit as this could damage the unit.
When replacing the fuse, be sure to use one that matches the
amperage described on the original fuse. If the fuse blows, check the
power connection and replace the fuse. If the fuse blows again after
replacement, there may be an internal malfunction. In such a case,
consult your nearest your’s dealer.
White RCA: Mono Audio Input
Yellow RCA:Video Input
Red wire :DC +12Volts Power Input (car battery )
Black wire: Ground (negative earth)
Replacing the Remote Control Battery
1)Always use new battery when replace the old set.
2)Do not attempt to charge, short-circuit, disassemble,
heat or burn used batteries, battery may be explode
PULL OUT
if mistreated.
3)Battery replacement is necessary when remote
PUSH IN
control acts sporadically or stops operating.
4)Do not drop, apply shock or step on the remote control.
5)Do not spill water on the remote control.
6)Do not place objects between the remote control and remote sensor.
7)Do not use remote control for the other equipments at the same time.
8)Do not leave the remote near any heat sources, or in a place subject to direct sunlight
(especially on the dashboard).
9) Keep the lithium battery out of the reach of children. Should the battery be swallowed, immediately
consult a doctor.
10)If the MONITOR does not operate even when you operate the remote control from a close range,
it is time to replace the battery (use CR-2025 lithium battery), refer ring to the label on the back of
the basic control.
11)Do not hold the battery with metallic tweezers, otherwise a short-circuit may occur.
6
Steps For Installing Headrest with Shroud
Setup work
Remove the headrest and set it in an uncluttered
work area. Pay the appropriate precautions to
ensure that it is not damaged during the installation.
CAUTION: make sure the screws are not long enough to go through
the headrest!
If you have any doubts about this type of installation, please consult
your local mobile electronics retailer. Cutting and making holes in
the headrest will cause electronic damage which is expensive to repair.
Measurements
Press the headrest with your fingers to make
sure there are no obstructions that would hinder
the installation. Use paper template to mark the
area to be cut.
Cut the headrest
Use an adjustable-depth blade, start
your cut 1/4 inch inside one corner and
cut diagonally across, stopping 1/4 inch in
from the other corner. Repeat this procedure
for the other two corners.
Remove foam & obstructions
Carefully peel off the material. Set the
adjustable blade to one inch depth and cut
around the edges of the hole, staying 1/4 inch
inside the edge. Pull up one corner of the foam
and use the blade to cut underneath. Remove
small section at a time and ensure to be the
uniform depth. Use a dremel or other appropriate
tools to remove other obstructions. Insert the monitor to
measure the fit and make adjustment if necessary
7
Route the cable through the headrest
Run the supplied cable through the opening
and out to the bottom of the headrest. If possible,
conceal the wires with a shaft covering.
Connect the power, ground and video leads to
test the MONITOR.
Before connecting the monitor, pull the
connecting cable through the headrest shroud as
shown in diagram. Place the headrest housing into the
opening and secure with correct fasteners.
Install the headrest shroud
Pull the connecting cable through the center of
the shroud as shown in diagram, and secure the
headrest shroud with correct fasteners
Insert the monitor
Push to insert the monitor
to the headrest shroud.
Removal
Insert the release key between the monitor and
headrest shroud gap and pull it out to remove the
monitor from headrest shroud.
8
Steps For Installing Sun-visor with Shroud
Setup work
Remove the visor and set it in an uncluttered
work area. Pay appropriate precautions to
ensure that it is not damaged during the installation.
CAUTION: make sure the screws are not long enough to go through
the visor!
If you have any doubts about this type of installation, please consult
your local mobile electronics retailer. Cutting and making holes in
the visor will cause electronic damage which is expensive to repair.
Measurements
Press push on the headliner with your fingers to make
sure there are no obstructions that would hinder
the installation. Use paper template to mark the
area to be cut.
Cut the visor
Use an adjustable-depth blade, start
your cut 1/4 inch inside one corner and
cut diagonally across, stopping 1/4 inch in
from the other corner. Repeat this procedure
for the other two corners.
Remove foam & obstructions
Carefully peel off the material. Set the
adjustable blade to one inch depth and cut
around the edges of the hole, staying 1/4 inch
inside the edge. Pull up one corner of the foam
and use the blade to cut underneath. Remove
small section at a time, ensure to be the
uniform depth . Use a dremel or other appropriate
tools to remove other obstructions. Insert the
monitor to measure the fit and make
adjustment if necessary.
9
Route the cable through the visor
Run the supplied cable through the opening
and out to the bottom of the visor. If possible,
conceal the wires using a shaft covering.
Connect the power, ground and video leads to
test the MONITOR. Before connecting the
monitor, pull the connecting cable assembly
through the visor housing as shown in diagram.
Place sun-visor shroud into the opening and
secure it with correct fasteners.
Install the sun-visor shroud
THIS SIDE UP
Pull the connecting cable through the center of
the housing as shown in diagram, and secure
the sun-visor shroud with correct fasteners
Insert the monitor
Push to insert the monitor
to the sun-visor shroud.
Removal
Insert the release key between the monitor and
visor shroud gap and pull it out to remove the
monitor from headrest shroud.
Operate your syst em in a safe and legal manner
When oper ate a motor vehi cle, it shoul d always be your highest priority to
maintain safe driving habi ts.
It is illegal in many areas of most count ries to drive with TV or MONITOR
on, when it is visible to the driver. Please check your local and state
laws gover ning the use of MOBILE ENTERTAINMENT SYSTEM in your area.
10
Rear side of headrest
Front side of headrest
11
Function setting
Press MENU button (1)from the remote or press manual button (1) from the monitor
2
to call out the function menu, press button (2 or 3) to the desired setting.
1
Video Signal
Picture Parameters
DDP
OSD Setup
Others
3
Monitor
Remote
OSD
Press Menu button (1) to enter video
signal input selection.
The symbol show current video input.
AV1
AV2
Return
2
1
MU
EXIT
ENT.
EXIT
SEL.
3
Monitor
Remote
Video Signal Picture Parameters
DDP
OSD Setup
Others
OSD
Press the button( 2or3) to move the
and choose video signal input.
Press menu button (1) to confirm your selection.
Move the symbol to RETURN and press
symbol
AV1
AV2
Return
menu button (1) to exit.
2
1
MU
EXIT
SET
RET
SEL.
3
Monitor
Remote
Video Signal
Picture Parameters
DDP
OSD Setup
Others
OSD
Press the button (2 or 3) to choose the picture
parameters setting.
Press MENU(1) to enter.
Contrast
Brightness
Hue
Saturation
Gamma Function
Scaling
2
1
Return
MU
EXIT
ENT.
EXIT
SEL.
3
Monitor
Remote
12
Video Signal
Picture Parameters
DDP
OSD Setup
Others
OSD
Press the button( 2or3) to adjust the
to choose “contrast.
symbol
Press menu button (1) to enter contrast setting.
[Contrast: Narrows or widens the gap between black & white
(darken & brighten)]
Contrast
Brightness
Hue
Saturation
Gamma Function
Scaling
2
1
Return
MU
EXIT
ADJ.
RET
SEL.
3
Monitor
Remote
Video Signal Picture Parameters
DDP
OSD Setup
Others
OSD
Press button 2: adjust contrast to brighten level.
Press button 3: adjust contrast to darken level.
Press button 1 to confirm setting.
[Contrast adjustable level: 0~100 . Preset: 50]
Contrast
50
2
1
MU EXIT
SAVE / EXIT
- / +
3
Monitor
Remote
Video Signal
Picture Parameters
DDP
OSD Setup
Others
OSD
Press the button( 2or3) to adjust the
to choose “brightness”.
symbol
Press menu button (1) to enter brightness setting.
[Brightness: Makes black appear darken or lighter]
Contrast
Brightness
Hue
Saturation
Gamma Function
Scaling
2
1
Return
MU
EXIT
ADJ.
RET
SEL.
3
Monitor
Remote
13
Video Signal
Picture Parameters
DDP
OSD Setup
Others
OSD
Press button 2: adjust brightness to lighter level.
Press button 3: adjust brightness to darken level.
Press button 1 to confirm setting.
[Brightness adjustable level: 0~100 . Preset: 50]
Brightness
50
2
1
MU EXIT
SAVE / EXIT
- / +
3
Monitor
Remote
Video Signal Picture Parameters
DDP
OSD Setup
Others
OSD
Press the button( 2or3) to adjust the
to choose “hue”.
symbol
Press menu button (1) to enter hue setting.
[Hue: adjusts reddish or green picture]
Contrast
Brightness
Hue
Saturation
Gamma Function
Scaling
2
1
Return
MU
EXIT
ADJ.
RET
SEL.
3
Monitor
Remote
Video Signal
Picture Parameters
DDP
OSD Setup
Others
OSD
Press button 2: increases greenish level.
Press button 3: increases reddish level.
Press button 1 to confirm setting.
[Hue adjustable level: 0~100 . Preset: 50]
Hue
50
2
1
MU EXIT
SAVE / EXIT
- / +
3
Monitor
Remote
14
Video Signal Picture Parameters
DDP
OSD Setup
Others
OSD
Press the button( 2or3) to adjust the
to choose “letter box”.
symbol
Press menu button (1) setup as letter box.
The symbol show current selection.
[An image with an aspect ratio of 4:3 (regular picture)]
Scaling
Full Screen
Letter Box
Paranoma
Return
2
1
MU
EXIT
SET.
RET
SEL.
3
Monitor
Remote
Video Signal
Picture Parameters
DDP
OSD Setup
Others
OSD
Press the button( 2or3) to adjust the
to choose “paranromal”.
symbol
Press menu button (1) setup as paranormal.
The symbol show current selection.
[An image with an aspect ratio of 4:3, with only the left and
right sides of the image being enlarged to fill the screen]
Scaling
Full Screen
Letter Box
Paranoma
Return
2
1
MU
EXIT
SET.
RET
SEL.
3
Monitor
Remote
Video Signal
Picture Parameters
DDP
OSD Setup
Others
OSD
Press Menu button (1) to enter picture clearness
setting.
The symbol show current video input.
Enable
Disable
Return
2
1
MU
EXIT
ADJ.
RET
SEL.
3
Monitor
Remote
15
Video Signal
Picture Parameters
DDP
OSD Setup
Others
OSD
Press the button( 2or3) to adjust the
to choose “saturation”.
symbol
Press menu button (1) to enter saturation setting.
[Makes color appear lighter or darker]
Contrast
Brightness
Hue
Saturation
Gamma Function
Scaling
2
1
Return
MU
EXIT
ADJ.
RET
SEL.
3
Monitor
Remote
Video Signal Picture Parameters
DDP
OSD Setup
Others
OSD
Press button 2: makes colors appear darker.
Press button 3: makes colors appear lighter.
Press button 1 to confirm setting.
[Saturation adjustable level: 0~100 . Preset: 50]
Saturation
50
2
1
MU EXIT
SAVE / EXIT
- / +
3
Monitor
Remote
Video Signal
Picture Parameters
DDP
OSD Setup
Others
OSD
Press the button( 2or3) to adjust the
to choose “gamma”.
symbol
Press menu button (1) to enter gamma setting.
[Gamma: Makes black light appear darken or lighter]
Contrast
Brightness
Hue
Saturation
Gamma Function
Scaling
2
1
Return
MU
EXIT
ADJ.
RET
SEL.
3
Monitor
Remote
16
Video Signal
Picture Parameters
DDP
OSD Setup
Others
OSD
Press button 2: appear 0 standard (preset).
Press button 3: select 1(brighten) .
Press button 1: to confirm setting.
Gamma Function
0
2
1
MU EXIT
SAVE / EXIT
- / +
3
Monitor
Remote
Video Signal Picture Parameters
DDP
OSD Setup
Others
OSD
Press the button( 2or3) to adjust the
to desired setting (scaling).
symbol
Press menu button (1) to enter scaling setting.
[Scaling: adjusts picture size full screen, letter box & paranormal]
Contrast
Brightness
Hue
Saturation
Gamma Function
Scaling
2
1
Return
MU
EXIT
ADJ.
RET
SEL.
3
Monitor
Remote
Video Signal
Picture Parameters
DDP
OSD Setup
Others
OSD
Press the button( 2or3) to adjust the
to choose “full screen:.
symbol
Press menu button (1) setup as full screen.
The symbol show current selection.
[An image with an aspect ratio of 4:3 enlarge to the left & right
edges of the screen]
Scaling
Full Screen
Letter Box
Paranoma
Return
2
1
MU
EXIT
SET.
RET
SEL.
3
Monitor
Remote
17
Video Signal Picture Parameters
DDP
OSD Setup
Others
OSD
Press the button( 2or3) to adjust the
to choose enable.
symbol
Press menu button (1) setup as clearness picture.
The symbol show current selection.
Enable
Disable
Return
Adjust the
symbol to RETURN and press
menu button (1) to exit.
[Set enable as smartnous technology support]
2
1
3
MU
EXIT
ADJ.
RET
SEL.
Monitor
Remote
Video Signal
Picture Parameters
DDP
OSD Setup
Others
OSD
Press the button( 2or3) to adjust the
to choose disable.
symbol
Press menu button (1) setup as clearness picture.
The symbol show current selection.
Enable
Disable
Return
Move the
symbol to “RETURN” and press
menu button (1) to exit.
[Set disable as normal picture]
2
1
MU
EXIT
ADJ.
RET
SEL.
3
Monitor
Remote
Video Signal
Picture Parameters
DDP
OSD Setup
Others
Press Menu button (1) to set the OSD.
Language Select
OSD Timeout
Transparency
Information
Memory Recall
Return
2
1
MU
EXIT
ADJ.
RET
SEL.
3
Monitor
Remote
18
Video Signal Picture Parameters
DDP
OSD Setup
Others
Press the button( 2or3) to adjust the
to choose “language”.
symbol
Press menu button (1) to enter language setting.
Language Select
OSD Timeout
Transparency
Information
Memory Recall
Return
[Setting On Screen Display language]
2
1
MU
EXIT
ADJ.
RET
SEL.
3
Monitor
Remote
Video Signal
Picture Parameters
DDP
OSD Setup
Others
Press the button( 2or3) to adjust the
to desired language (English).
symbol
Press menu button (1) setup language as English.
The symbol show current selection.
Language Select
English
Exit
Move the
symbol to “RETURN” and press
menu button (1) to exit.
[Set disable as normal picture]
2
1
MU
EXIT
SET.
RET
SEL.
3
Monitor
Remote
Video Signal
Picture Parameters
DDP
OSD Setup
Others
Press Menu button (1) to set OSD appear timing.
Language Select
OSD Timeout
Transparency
Information
Memory Recall
Return
2
1
MU
EXIT
ADJ.
RET
SEL.
3
Monitor
Remote
19
Video Signal Picture Parameters
DDP
OSD Setup
Others
Press button 2: increase OSD timeout.
Press button 3: reduce OSD timeout.
Press button 1 to confirm setting.
[Timout level: 10~60 . Preset:30 seconds]
OSD Timeout
30
2
1
MU EXIT
SAVE / EXIT
- / +
3
Monitor
Remote
Video Signal
Picture Parameters
DDP
OSD Setup
Others
Press the button( 2or3) to adjust the
to choose “transparency” setting.
symbol
Press menu button (1) to enter OSD transparency
Language Select
OSD Timeout
Transparency
Information
Memory Recall
Return
setting.
[Transparency: makes solid or transparency OSD display]
2
1
MU
EXIT
ADJ.
RET
SEL.
3
Monitor
Remote
Video Signal
Picture Parameters
DDP
OSD Setup
Others
Press button 2: set increase transparency.
Press button 3: set reduce transparency .
Press button 1 to confirm setting.
Move the
symbol to “RETURN” and press
menu button (1) to exit.
[Transparency adjustable level: 0~7 . Preset:0]
Transparency
0
2
1
MU EXIT
SAVE / EXIT
- / +
3
Monitor
Remote
20
Video Signal Picture Parameters
DDP
OSD Setup
Others
Press the button( 2or3) to adjust the
to choose “information”.
symbol
Press menu button (1) to enter information.
Language Select
OSD Timeout
Transparency
Information
Memory Recall
Return
[Appear video input information]
2
1
MU
EXIT
ADJ.
RET
SEL.
3
Monitor
Remote
Video Signal
Picture Parameters
DDP
OSD Setup
Others
Show video signal input information.
Move the
symbol to “RETURN” and press
menu button (1) to exit.
[Set disable as normal picture]
Information
Source: Av1
Format: NTSC
HS: 15.7 Khz
VS: 59.8Hz
2
1
MU
EXIT
SET.
RET
SEL.
3
Monitor
Remote
Video Signal
Picture Parameters
DDP
OSD Setup
Others
Press Menu button (1) set return tp factory default
setting.
Language Select
OSD Timeout
Transparency
Information
Memory Recall
Return
2
1
MU
EXIT
ADJ.
RET
SEL.
3
Monitor
Remote
21
Video Signal
Picture Parameters
DDP
OSD Setup
Others
OSD
Move the
symbol to “RETURN” and press
menu button (1) to exit.
[Fully exit the setting]
Exit
VCOM Adjust
Display Model: Rotate
2
1
MU
ADJ.
EXIT
RET
SEL.
3
Monitor
Remote
Video Signal
Picture Parameters
DDP
OSD Setup
Others
OSD
Adjust to the picture rotate
Exit
VCOM Adjust
Display Model: Rotate
2
1
MU
ADJ.
EXIT
RET
SEL.
3
Monitor
Remote
Press button 2: set volume increase.
Press button 3: set volume reduce.
Press button 1 to mute the sound, press again
to restore the previous volume level.
[Volume adjustable level: 0~100 . Preset:50]
2
1
50
Monitor
3
Remote
22
Specifications:
LCD Drive Method: a-SI TFT Active Matrix
Visible Screen Size: 7 Inch Wide Screen (Diagonal)
Aspect Ratio: 16:9
Display Format: 480 x RGB x 234
Number of Pixels: 336,960
Response Time: 15ms
Backlight : High Brightness CCFT
Luminance: 350 cd/m2 #3
Backlight Life: 10,000 Hrs #1
Contrast Ratio: 300:1
Viewing Angle: (H/V): 120o / 100o
Operation Temperature: -20oC ~ 70oC / -2oF ~ 158oF
Video Color System Input: NTSC & PAL Compatible
On Screen Display: English
Rear Video Input Terminals: RCA x 1 (1 Vp-p, 75 ohm)
Front Video Input Terminals: 3.5mm Jack x1 (1 Vp-p, 75 ohm)
Front Audio Input Terminals: 3.5mm Jack x1
Front Audio Output Terminals: 3.5mm Jack x1
Remote Control: Included
Volume / Brightness / Contrast / Saturation / Hue: Adjustable
Blue Screen: Yes
Power Input: DC12 Volts car battery (negative earth)
Current Consumption: 6 W Max
Weight: 154g
Size: 186 x 105 x 22.5 cm (L x W x H)
73.23 x 41.34 x 8.86 inch (L x W x H)
#1 A measure of the time unit screen brightness declines by half under continuous viewing
in a car/room at 25oC with screen brightness in standard mode. (50% original brightness)
#2 A measure of the unit temperature declines in a car/room at 25oC
with screen brightness in standard mode. (50% original brightness)
#3 A measure of the backlight 350cd/m2 brightness will in standard
lamp voltage at 560 Vrms.
.
Pyle, Inc.
1600 63rd street
Brooklyn, NY 11204
0
8
6 8 8 8 8 8 8 0 0 0
23
|