Dimplex Indoor Fireplace BF series User Manual

PRACTICAL USER’S GUIDE  
FOR THE  
ELECTRIC FIREPLACE  
BF series with filter and LED logset  
Quality checked by:  
Valued Customer,  
We are pleased that you have chosen to purchase an electric fireplace  
manufactured by Dimplex North America Ltd.  
Over the years, valuable memories will occur around the warmth and  
comfort of your hearth. Thank you for allowing our product to be the backdrop  
for those special moments.  
7207920100rev00  
 
CONTENTS  
PAGE 1  
PAGE 2  
Important Instructions  
Model and Serial Number  
Information  
PAGE 4  
PAGE 6  
PAGE 9  
PAGE 10  
Operation  
Maintenance  
Accessories  
Warranty  
 
IMPORTANT INSTRUCTIONS  
SAVE THESE INSTRUCTIONS  
PLEASE RETAIN THIS USER’S GUIDE FOR FUTURE REFERENCE  
When using electrical appliances, basic precautions should always be followed to reduce the risk of fire,  
electric shock, and injury to persons, including the following:  
1. Read all instructions before using the electric fireplace.  
2. This fireplace is hot when in use. To avoid burns, do not let bare skin touch hot  
surfaces. The trim around the heater outlet becomes hot during heater operation. Keep combustible  
materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9m) from  
the front of the unit.  
3. Extreme caution is necessary when any heater is used by or near children or invalids and whenever the  
unit is left operating and unattended.  
4. Young children should be supervised to ensure that they do not play with the appliance.  
5. The appliance is not intended for use by young children or infirmed persons unless they have been  
adequately supervised by a responsible person to ensure they can use the appliance safely.  
6. The appliance must be positioned so that the plug is accessible.  
7. Always unplug the electric fireplace when not in use.  
8. If the supply cord is damaged, it must be replaced by the manufacturer, or its service agent, or a  
qualified person in order to avoid a hazard.  
9. Do not operate any unit with a damaged cord or plug, or if the heater has malfunctioned, or if the electric  
fireplace has been dropped or damaged in any manner. Return heater to authorized service facility for  
examination, electrical or mechanical adjustment, or repair.  
10. Do not use outdoors.  
11. Do not use this fireplace in the immediate surroundings of a bath, a shower or a swimming pool.  
12. Do not install the fireplace directly on carpet or a similar surface which may restrict air circulation  
beneath the unit.  
13. Do not run the cord under carpeting. Do not cover cord with throw rugs, runners, or the like. Arrange  
cord away from traffic area and where it will not be tripped over.  
14. Do not locate the heater immediately below a fixed socket-outlet.  
15. Do not locate the appliance in front of a fixed socket-outlet  
16. To disconnect the fireplace, turn the controls off, then remove the plug from the outlet.  
17. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an  
electric shock or fire, or damage to the heater.  
18. To prevent a possible fire, do not block air intake or exhaust in any manner. Do not use on soft surfaces,  
like a bed, where openings may become blocked.  
19. All electrical heaters have hot and arching or sparking parts inside. Do not use in areas where gasoline,  
paint, or flammable liquids are used or stored or where the unit will be exposed to flammable vapors.  
20. Do not modify the electric fireplace. Use it only as described in this manual. Any other use not  
recommended by the manufacturer may cause fire, electric shock or injury to persons.  
21. Avoid the use of an extension cord. Extension cords may overheat and cause a risk of fire. If you must  
use an extension cord, the cord must be 3-core type and have a rating no less than 13 amps.  
22. Do not burn wood or other materials in the electric fireplace.  
23. Do not strike the fireplace glass.  
24. Always use a certified electrician should new circuits or outlets be required.  
25. Always use properly grounded, fused and polarized outlets.  
26. Disconnect all power supply before performing any cleaning, maintenance or relocation of the unit.  
27. When transporting or storing the unit and cord, keep in a dry place, free from excessive vibration and  
store so as to avoid damage.  
28. WARNING: In order to avoid overheating, do not cover the heater  
29. CAUTION In order to avoid a hazard due to the inadvertent resetting of the thermal cutout, this  
:
appliance must not be supplied through an external switching device, such as a timer, or connected  
to a circuit that is regularly switched on and off by the utility  
_____________________________________________________________________________________________________________________________________________________________________________________  
NOTE: Procedures and techniques that are considered important enough to emphasize.  
CAUTION: Procedures and techniques which, if not carefully followed, will result in damage to the  
equipment.  
WARNING: Procedures and techniques which, if not carefully followed, will expose the user to the risk of  
fire, serious injury, illness or death.  
1
 
IMPORTANT INSTRUCTIONS  
If you have any questions about our products please have the product model and  
serial numbers available upon calling Dimplex customer service. To locate the  
model and serial number labels see below.  
Model Number  
Serial Number  
Serial Number  
Firebox  
Model Number  
2
 
Model Number  
Serial Number  
Carton  
3
 
OPERATION  
REMOTE CONTROL  
The remote control has a range of approximately 50ft.  
(15.25m), it does not have to be pointed at the fireplace and  
can pass through most obstacles (including walls).  
Remote Control Initialization  
This procedure is may be required if there is a loss of power  
to the remote control in the fireplace. (i.e. power failure,  
breaker tripped, main power switch is turned off) or if a new  
remote is used.  
1. Ensure that power is supplied through main service  
panel.  
2. Locate manual controls (FIGURE 2)  
3. Activate main power switch.  
4. Press (on) button located on the Manual Selection  
Control for 3 seconds (FIGURE 3). All 3 indicators will  
flash.  
FIGURE 1  
Press the ON button on the transmitter (FIGURE 1). The  
indicators will flash rapidly and then turn off. This will  
synchronize the remote control transmitter and receiver.  
A. Remote Control Usage  
The remote control operates the fireplace levels  
sequentially. The level is increased every time the ON  
button on the transmitter is pressed. The fireplace can be  
turned off at any point by pressing the OFF button on the  
remote control transmitter.  
Thermostat  
control  
FIGURE 2  
Main power switch  
Level 1: The flame effect is turned on and the first red indicator light is activated.  
Level 2: The flame effect remains on, and the PurifireTM is activated. The first and second red  
indicator lights are activated.  
Level 3: The flame effect remains on, the heater is activated, and all three red indicator lights  
are activated.  
4
 
MANUAL CONTROLS  
The fireplace can also be controlled in a similar manner to the remote control with switches  
located on the fireplace (FIGURE 3).  
A. On Switch  
Operates fireplace in the same manner as the remote control transmitter. Pressing this button  
has the same effect as the ON button on the remote control. Pressing once to the activates  
Level 1, twice activates Level 2, three times activates Level 3.  
B. Off Switch  
Pressing this button has the same effect as the OFF button on the remote control. Pressing  
once to shut the unit off.  
B. OFF SWITCH  
A. ON SWITCH  
LEVEL 1 INDICATOR  
LEVEL 2 INDICATOR  
FIGURE 3  
LEVEL 3 INDICATOR  
HEATER THERMOSTAT CONTROL  
To adjust the temperature to your individual requirements, turn the thermostat control  
clockwise all the way to turn on the heater. When the room reaches the desired temperature,  
turn the thermostat knob counter clockwise until you hear a click. Leave in this position to  
maintain the room temperature at this setting. For additional heat, turn clockwise until you  
hear the click again and the heater will turn on  
NOTE:  
The heater may emit a slight harmless odor when first used. This odor is a normal condition  
caused by initial heating of internal parts and will not occur again.  
5
 
THE TEMPERATURE CUTOUT SWITCH  
The heater on this fireplace is protected with a safety device to prevent overheating.  
Should the heater overheat, an automatic cut out will turn the heater off. The heater will re-  
activate once the heater has cooled. The overheat cutout may be triggered if the filter is  
dirty. Follow filter maintenance on page 8.  
CAUTION  
If the heater continuously resets, disconnect the power at the main service panel and call  
your local dealer.  
MAINTENANCE  
WARNING  
Disconnect all power coming to fireplace at main service panel before attempting  
maintenance or cleaning to reduce risk of fire, shock or damage to persons.  
NOTE  
Allow at least 5 minutes for light bulbs to cool off before touching bulbs to avoid accidental  
burning of skin.  
TOOL REQUIREMENTS  
Screwdriver  
LIGHT BULB REPLACEMENT  
Allow at least 5 minutes for light bulbs to cool off before touching bulbs to avoid accidental  
burning of skin.  
Light bulbs need to be replaced when you notice a dark section of the flame or when the  
clarity and detail of the log exterior disappears. There are four bulbs under the log set  
which generate the flames and embers.  
LIGHT BULB REQUIREMENTS  
Quantity of 4 clear chandelier or candelabra bulbs with an E-14 socket base, 60 watt  
rating.  
DO NOT EXCEED 60 WATTS PER BULB.  
CAUTION  
When handling log only apply force to the ember bed section not directly to the logs.  
HELPFUL HINTS  
It is a good idea to replace all light bulbs at one time if they are close to the end of their  
rated life. Group replacement will reduce the number of times you need to open the unit to  
replace light bulbs. Long life bulbs are recommended to reduce the frequency of bulb  
changes.  
6
 
To access the light bulb area  
1. Open steel curtain (remove glass doors if  
applicable).  
2. Remove two screws on log bracket and set  
aside. (FIGURE 4)  
3. Pull front edge of plastic ember bed or plastic  
grate up and forward until rear tab releases  
from the ledge located at the bottom of the  
mirror. (FIGURE 5)  
Note: Log set fits tightly into firebox, some force  
may be necessary to remove.  
SCREWS  
4. Set logset in front of firebox.  
FIGURE 4  
5. Disconnect the logset LED wire harness from  
unit. (FIGURE 6)  
6. Examine the bulbs to determine which bulbs  
require replacement.  
7. Unscrew bulbs counter clockwise.  
8. Insert new bulbs.  
9. Re-connect the logset LED wire harness to the  
unit.  
10.Replace the log by inserting the rear tab of the  
logset under the back ledge of the fireplace  
and push down on the front edge of the logset  
until it snaps into place. (FIGURE 5)  
FIGURE 5  
11.Replace log grate using two screws previously  
removed.  
FIGURE 6  
7
 
PURIFIRE™ FILTER  
The Purifire™ filter supplied in your fireplace is reusable and washable. The filter should  
be cleaned or replaced on average once a year. To clean the filter gently tap filter on a  
hard surface to dislodge any loose dirt or debris, and then clean with water. No soap or  
cleaning products are recommended. The filter size is 20”(508mm) X 10”(254mm) X  
1”(25.4mm) rated at MERV 10. If using an after market filter follow the manufacturers  
recommended replacement instructions.  
To replace filter:  
1. Remove the 2 mounting screws from the air filter bracket.  
2. Slide forward to remove the air filter bracket assembly from the firebox.  
3. Slide filter out of air filter bracket.  
4. Reassemble in reverse order as above.  
NOTE  
If after market air filter is used ensure it is installed according to the manufacturers  
recommended instructions.  
FIGURE 7  
8
 
Mirror Cleaning  
The mirror is cleaned in the factory during the assembly operation. During shipment,  
installation, handling, etc., the mirror surface may collect dust particles; these can be  
removed by buffing lightly with a clean dry cloth.  
To remove fingerprints or other marks, the mirror can be cleaned with a damp cloth using  
good quality household glass cleaner. The mirror should be completely dried with a lint  
free cloth to prevent water spots. To prevent scratching, do not use abrasive cleaners or  
spray liquids on the clear door surface.  
ACCESSORIES  
Please contact your local dealer for genuine Dimplex accessories. Example: Glass door  
kits, brass and stainless steel trims, and cabinets designed to fit your fireplace.  
9
 
WARRANTY  
Dimplex Electric Fireplaces are tested and inspected prior to shipment and are  
guaranteed from defect to the purchaser of each new product. Any part which proves  
to be defective in material or workmanship under normal use within one year will  
be repaired or replaced without charge.* The Company will not be responsible for  
any expense incurred for installation, removal for service, or transportation costs.  
Any such defect should be brought to the attention of the Dealer where the product  
was purchased and is authorized to repair or replace within the terms of this warranty.  
The Company’s only obligation under this warranty will be at its sole  
option to repair or replace any part proving defective or to refund the  
purchase price thereof.  
The owner/user assumes all other risks, if any, including the risk of any direct,  
indirect or consequential loss or damage arising out of the use of or inability to  
use the product.  
The warranty will not apply if, in the sole judgment of the Company, damage or failure has  
resulted from accident, alteration, misuse, abuse, incorrect installation, or operation on an  
incorrect power source.  
The foregoing is in lieu of all other warranties expressed, implied, or  
statutory, and the Company neither assumes, nor authorizes any person  
to assume for it any other obligation, or liability in connection with said  
product.  
*Light bulbs are not covered in the warranty.  
SERVICE  
Contact your local dealer for service or warranty information.  
The product complies with the European Safety Standard EN60335-2-30 and the  
European Standard for Electromagnetic Compatibility (EMC) EN55014, EN6055-2 and  
EN60555-3 which cover the essential requirements of EEG Directives 73/23 and 89/336.  
10  
 

Conair Styling Iron CS32 User Manual
Cornelius Frozen Dessert Maker P N 629088733 User Manual
Curtis Digital Photo Frame DPB770 User Manual
Extron electronic Speaker SI 26X User Manual
Ferris Industries Lawn Mower is3100z series User Manual
Fusion Speaker CP SW100 User Manual
Gaggenau Ventilation Hood AH 530 790 User Manual
Genicom Printer LN45 User Manual
Gitzo Camcorder Accessories GT3530 User Manual
Global Machinery Company Trimmer GLT25 User Manual