Radio Shack Cell Phone TAD 723 User Guide

43-723.fm Page 1 Monday, May 22, 2000 10:26 AM  
TAD-723 Digital Telephone  
Answering System  
with Day/Time Voice Stamp  
 
43-723.fm Page 3 Monday, May 22, 2000 10:26 AM  
ˆ Contents  
Features .................................................................................................................................. 4  
Installation .............................................................................................................................. 5  
Connecting the TAD to the Phone Line ............................................................................ 5  
Connecting Power ............................................................................................................ 5  
Installing the Backup Batteries ......................................................................................... 5  
Preparation ............................................................................................................................. 6  
Turning the TAD On/Off .................................................................................................... 6  
Adjusting the Volume ........................................................................................................ 6  
Setting the Day and Time ................................................................................................. 6  
Recording the Outgoing Messages (OGM) ...................................................................... 7  
Setting the Incoming Message Length ............................................................................. 8  
Checking an OGM ............................................................................................................ 8  
Setting the Number of Rings ............................................................................................ 8  
Basic Operation ..................................................................................................................... 9  
Setting the TAD to Answer Calls ...................................................................................... 9  
Using the Announce-Only Feature ................................................................................... 9  
Screening Calls .............................................................................................................. 10  
Recording a Memo ......................................................................................................... 10  
Playing Incoming Messages/Memos .............................................................................. 10  
Deleting Messages ......................................................................................................... 10  
Remote Operation ................................................................................................................ 11  
Changing the Remote Operation Security Code ............................................................. 11  
Operating the TAD from a Remote Location ................................................................... 11  
Remote Commands ........................................................................................................ 12  
Troubleshooting ................................................................................................................... 13  
Care and Maintenance ......................................................................................................... 14  
The FCC Wants You to Know ......................................................................................... 15  
Lightning ......................................................................................................................... 15  
3
Contents  
 
43-723.fm Page 4 Monday, May 22, 2000 10:26 AM  
ˆ Features  
Your RadioShack Digital Telephone Answer-  
ing System is a sophisticated, fully digital  
message center.  
Remote Operation  
— lets you use a touch-  
tone phone (or rotary phone and pocket tone  
dialer) to operate the TAD while you are  
away from your home or office.  
Fully digital means the TAD (Telephone An-  
swering Device) stores all messages on a  
computer chip. This gives you advanced ca-  
pabilities over tape-based answering ma-  
chines. For example, you can save or delete  
individual messages.  
Programmable Remote Operation Securi-  
ty Code  
— lets you set your own 3-digit se-  
curity code for remote operation.  
Remote Answer-On  
— lets you call the TAD  
from a remote location and set it to answer  
calls.  
Because your TAD is fully digital, there are  
no tape mechanisms to wear out and no  
tapes to bother with.  
Adjustable Ring Number  
— you can set the  
TAD to answer after two, four, or seven  
rings.  
The TAD has these features:  
High Capacity  
Toll-Saver  
— lets you avoid unnecessary toll  
— lets you record up to 20  
minutes of messages and memos.  
charges when calling long-distance to check  
your messages.  
Voice Day/Time Stamp  
— records the day  
Selectable Incoming Message Length  
and time each message was recorded.  
lets you set the maximum length of a caller’s  
message to 1 or 5 minutes.  
Digitally-Synthesized Voice  
through operation of many of the system’s  
features.  
— guides you  
Memory Full Warning  
— lets you know  
when the TAD’s memory is full.  
Call Screening  
— lets you listen to incoming  
Memory Backup  
sages in case of a power failure.  
calls so you can decide whether or not to an-  
swer a call.  
— protects stored mes-  
Phone Pick-Up Detection  
Messages Indicator LED  
— stops record-  
— flashes to let  
ing a caller’s message when you pick up any  
phone on the same line as the TAD, so you  
can talk to the caller.  
you know you have new messages.  
LED Message Counter  
— shows the num-  
ber of messages the TAD recorded.  
Multiple Outgoing Message (OGM) Capac-  
Room Monitor  
— lets you monitor, using a  
ity  
— lets you set the TAD to play one of two  
remote phone, the room where the TAD is in-  
stalled for 30 seconds.  
outgoing messages then record the caller’s  
message, or just play an announcement  
without recording a message.  
Memo Recording  
— lets you leave messag-  
es for yourself or others in your home or of-  
fice.  
4
Features  
 
43-723.fm Page 5 Monday, May 22, 2000 10:26 AM  
ˆ Installation  
Select a location for the TAD that is near  
both a telephone jack and an easily accessi-  
ble AC outlet, and out of the way of normal  
activities.  
ers at least 300 mA. Its center tip must  
be set to positive and its plug must fit the  
9V  
TAD’s  
jack. The supplied adapter  
meets these specifications. Using an  
adapter that does not meet these speci-  
fications could damage the TAD or the  
adapter.  
CONNECTING THE TAD TO  
THE PHONE LINE  
• Always connect the adapter to the TAD  
before you connect it to the power  
source. When you finish, disconnect the  
AC adapter from the power source  
before you disconnect it from the TAD.  
Notes:  
• If the phone line jack is not a modular  
jack, you must update the wiring. You  
can convert the wiring yourself, using  
jacks and adapters available at your  
local RadioShack store. Or, you can let  
the phone company update it.  
Follow these steps to connect the power:  
1. Insert the barrel plug of the supplied AC  
DC 9V 300mA  
adapter into the  
jack on  
• The USOC number of the jack to be  
installed is RJ11C.  
the back of the TAD.  
2. Plug the other end of the AC adapter  
into a standard AC outlet.  
1. Unplug your telephone’s modular cord  
from the modular phone line jack and  
TO PHONE  
plug it into the  
back of the TAD.  
jack on the  
Each time you connect the TAD to AC pow-  
er, the LOW BATTERY indicator lights (if no  
backup batteries are installed), and the TAD  
initializes itself, then beeps when it finishes.  
2. Plug one end of the supplied modular  
TO LINE  
cord into the  
the TAD.  
jack on the back of  
Notes:  
• Do not press any of the TAD’s buttons  
while you are plugging the adapter into  
the AC outlet. If you accidentally press a  
button, reset the TAD by unplugging the  
adapter from the AC outlet then re-  
inserting it.  
• The TAD cannot operate without AC  
power.  
3. Plug the cord’s other end into the phone  
line jack.  
INSTALLING THE BACKUP  
BATTERIES  
CONNECTING POWER  
Cautions:  
If AC power fails or you unplug the TAD, four  
AAA batteries (not supplied) is needed to  
save any recorded messages and the set-  
You must use a power source  
that supplies 9V DC and deliv-  
!
5
Installation  
 
43-723.fm Page 6 Monday, May 22, 2000 10:26 AM  
Warning:  
tings for the day, time, and security code. We  
recommend you use RadioShack alkaline  
batteries.  
Dispose of the old batteries  
promptly and properly. Do not bury or burn  
them.  
Cautions:  
1. Use a Phillips screw-  
driver to remove the  
screw on the battery  
compartment cover.  
To avoid losing stored information, be  
sure the AC adapter is plugged in and  
connected to the TAD before you  
replace the batteries.  
2. Place the batteries in  
the compartment according to the polar-  
• Always use fresh batteries of the  
required size and type.  
+
ity symbols ( and ) marked inside.  
3. Replace the cover and secure it with the  
screw.  
• Always remove old or weak batteries.  
Batteries can leak chemicals that can  
destroy electronic parts.  
Replace the batteries when the LOW BAT-  
TERY indicator lights while the TAD is con-  
nected to AC power.  
• Do not mix old and new batteries or dif-  
ferent types of batteries.  
ˆ Preparation  
You can also turn on the TAD remotely  
(see “Remote Commands” on Page 12).  
ADJUSTING THE VOLUME  
ON/OFF  
Press  
VOLUME  
or  
to adjust the volume  
VOLUME  
to a comfortable listening level. The volume  
level (0–7) appears on the display. The TAD  
beeps three times when it reaches the maxi-  
mum volume level.  
TURNING THE TAD ON/OFF  
SETTING THE DAY AND  
TIME  
ON/OFF  
To turn on the TAD, simply press  
The TAD beeps twice.  
.
Follow these steps to set the current day and  
time so the TAD can record the day/time  
voice stamp on each memo and incoming  
message.  
ON/OFF  
To turn off the TAD, press  
again.  
Notes:  
• Once you turn on the TAD, it is set to  
answer calls (see “Setting the TAD to  
Answer Calls” on Page 9).  
Notes:  
• The day/time voice stamp automatically  
defaults to Sunday, 12 AM when you  
connect the TAD to power, and does not  
6
Preparation  
 
43-723.fm Page 7 Monday, May 22, 2000 10:26 AM  
advance until you set the correct day  
and time.  
RECORDING THE  
OUTGOING MESSAGES  
(OGM)  
CL and 0 flash on the display until you  
set the day and time.  
The TAD has a built-in outgoing message  
that says, “Hello, please leave a message af-  
ter the tone.” Use this message or record  
your own. The TAD lets you record three  
separate messages, and it operates differ-  
ently based on which message you select  
(see “Using the Announce-Only Feature” on  
Page 9).  
• If you do not press a button for about 10  
seconds after the TAD says an instruc-  
tion, the TAD exits setup. Start over at  
Step 1.  
ON/OFF  
1. If the TAD is off, press  
beeps twice.  
. The TAD  
OGM 1  
2.  
After playing your outgo-  
and  
TIME  
2. Hold down  
until the TAD  
ing message (either the built-in mes-  
sage or one you record), the TAD lets  
callers record a message of up to 1 or 5  
minutes.  
announces the day of the week (about 2  
seconds). For example TAD says “Sun-  
day”, and the display shows 7.  
Display  
Day of the Week  
Monday  
AO  
(announcement only). The TAD  
plays your outgoing message, but does  
not let the caller record a message.  
1
2
3
4
5
6
7
Tuesday  
Wednesday  
Thursday  
Friday  
Follow these steps to record an OGM.  
Note:  
The maximum length for each outgo-  
ing message is 3 minutes. As you record, the  
display counts up the recording time and  
beeps when you reach the maximum mes-  
sage length.  
Saturday  
Sunday  
SKIP  
REPEAT  
to set the day.  
3. Press  
or  
ANNOUNCE SELECT  
1, 2,  
AO  
or  
1. Slide  
to  
The TAD announces the day of the  
week as you press the button.  
to select the message you want to  
record.  
TIME  
4. Press  
to store the day of the week.  
5. Repeat Steps 3–4 to store the hour and  
minute.  
Note:  
The TAD uses the 12-hour time  
format. Be sure to set the correct AM or  
PM hour.  
6. The TAD announces the current day,  
hour and minutes.  
To hear the current day of the week and  
TIME  
time, press  
.
7
Preparation  
 
43-723.fm Page 8 Monday, May 22, 2000 10:26 AM  
ANNOUNCE  
2. Hold down  
until you hear a  
3. To stop the outgoing message before it  
STOP  
beep (about 2 seconds).  
ends, press  
.
SETTING THE NUMBER OF  
RINGS  
The ring select switch on the right side of the  
TAD controls how long the TAD waits before  
it answers a call. Slide the switch to the ap-  
propriate position.  
3. After the beep, begin speaking your  
message about 8 inches away from the  
microphone (located on the front of the  
TAD).  
2
4
7
— The TAD answers after two rings.  
— The TAD answers after four rings.  
— The TAD answers after seven rings.  
CODE/STOP  
4. Press  
to stop recording.  
The TAD automatically repeats the mes-  
sage then beeps.  
TS (Toll Saver)  
— If there are new messages,  
the TAD answers after two rings. Otherwise,  
the TAD answers after four rings. This lets  
you avoid unnecessary charges when calling  
by long-distance to check your messages. If  
you hear more than two rings, you know you  
can hang up because the TAD has no new  
messages.  
SETTING THE INCOMING  
MESSAGE LENGTH  
INCOMING  
1
5 MINUTES  
Slide  
to or to restrict  
the length of incoming messages.  
CHECKING AN OGM  
Follow these steps to check any OGM at any  
time.  
ANNOUNCE SELECT  
1, 2,  
AO  
or  
1. Slide  
to  
to select the desired OGM.  
ANNOUNCE  
2. Press  
to play the OGM.  
8
Preparation  
 
43-723.fm Page 9 Monday, May 22, 2000 10:26 AM  
ˆ Basic Operation  
and beeps twice, waits 10 seconds for  
any remote operation commands, then  
hangs up (see “Remote Commands” on  
Page 12). The TAD cannot record addi-  
tional messages until you delete some  
of the old messages (see “Deleting Mes-  
sages” on Page 10).  
SETTING THE TAD TO  
ANSWER CALLS  
ON/  
To set the TAD to answer calls, press  
OFF  
. The display turns on and the TAD  
beeps twice.  
• Many local phone companies use calling  
party control (CPC) to signal that the  
caller has hung up. Your TAD can recog-  
nize a CPC signal and release the line. If  
the TAD records phone company mes-  
sages or dial tones, your local phone  
company probably does not use CPC.  
Notes:  
USING THE ANNOUNCE-  
ONLY FEATURE  
You can use a remote phone to set the  
TAD to answer calls (see “Remote Com-  
mands” on Page 12).  
Your TAD’s announce-only feature lets you  
set the TAD to play a message for the caller,  
then automatically hang up without letting the  
caller leave a message.  
To set the TAD to not answer calls, turn  
ON/OFF  
it off by pressing  
.
When the TAD answers a call, the outgoing  
message plays, then the TAD beeps and be-  
gins recording.  
AN-  
To select the announce-only mode, slide  
NOUNCE SELECT  
AO AO  
appears. When  
the TAD receives a call, it plays the an-  
nounce-only message then hangs up.  
to  
.
The caller can leave a message of up to 5  
INCOM-  
minutes in length depending on the  
ING  
ANNOUNCE  
To turn off announce-only, slide  
setting (see “Setting the Incoming Mes-  
SELECT  
1
2
to either or .  
sage Length” on Page 8). After the caller  
hangs up or is silent for more than 7 sec-  
onds, or the maximum message length is  
reached, the TAD hangs up and resets to an-  
swer the next call. The MESSAGE indicator  
flashes to indicate an incoming message has  
been recorded.  
Notes:  
You must record an announce-only mes-  
sage in order to use this feature.  
• When the TAD is set for announce-only,  
you cannot set it to record calls using  
the remote commands (see “Remote  
Commands” on Page 12).  
Notes:  
• The MESSAGE indicator flashes rapidly  
when the memory is full.  
• If the TAD answers a call when its mem-  
ory is full, it announces “Memory is full”  
9
Basic Operation  
 
43-723.fm Page 10 Monday, May 22, 2000 10:26 AM  
the last message, the TAD says, “End of  
messages.”  
SCREENING CALLS  
To screen your calls, let the TAD answer.  
Listen to the caller’s message through the  
TAD’s speaker. If you decide to answer the  
call, pick up any phone connected to the  
same phone line as the TAD. The TAD stops  
recording and resets to answer the next call.  
After you play the messages, the MES-  
SAGE indicator lights steadily and the  
TAD automatically saves the messages  
and resets to answer calls.  
PAUSE/  
2. To replay the messages, press  
PLAY  
.
RECORDING A MEMO  
Note:  
sages, press  
resumes automatically after 1 minute or  
when you press  
To pause while listening to mes-  
A memo is a message that you record by  
speaking directly into the TAD, without call-  
ing in on the phone. Follow these steps to  
record a memo up to 3 minutes long.  
PAUSE/PLAY  
. The playback  
PAUSE/PLAY  
again.  
3. During message playback, you can  
repeat the current message, or skip  
backward or forward to the previous or  
next message.  
MEMO  
1. Press  
and  
the TAD beeps.  
The display timer  
starts counting.  
Record  
memo.  
your  
To repeat the current message, press  
REPEAT  
.
CODE/  
2. When you finish speaking, press  
To skip backward to any message,  
STOP  
.
The message indicator light  
REPEAT  
press  
until you reach the  
flashes until you play the memo. The  
light remains on until you delete played  
memos (see “Deleting Messages”). To  
play back a memo, see “Playing Incom-  
ing Messages/Memos.”  
message number you want to hear.  
To skip forward to the next message,  
SKIP  
press  
.
4. To stop message playback at any time,  
CODE/STOP  
press  
.
PLAYING INCOMING  
MESSAGES/MEMOS  
DELETING MESSAGES  
The MESSAGE indicator flashes after the  
TAD records one or more incoming messag-  
es or memos. The display shows how many  
messages were recorded.  
You can delete  
messages indi-  
vidually  
during  
playback, or all at  
once after play-  
back.  
1. To listen to all messages (including  
PAUSE/PLAY  
memos), press  
.
To delete a particular incoming message or  
The TAD plays each recorded message  
in sequence, beginning with the first new  
message. Before each message, the  
TAD announces the day and time the  
message was recorded. After playing  
DELETE  
memo (after listening to it), press  
mediately during playback.  
im-  
To delete all messages after playback, hold  
DELETE  
down  
for about 2 seconds. The TAD  
says, “Messages deleted”. The display  
10  
Basic Operation  
 
43-723.fm Page 11 Monday, May 22, 2000 10:26 AM  
Note:  
DELETE  
before playback  
shows 0 and the MESSAGE indicator light  
If you press  
turns off.  
of all messages, the TAD beeps three times.  
You cannot delete all messages until you  
play back all new messages.  
ˆ Remote Operation  
While you are away from your home or of-  
fice, you can use a touch-tone phone or a  
pulse (rotary) phone with a pocket tone dialer  
to enter your remote operation security code  
and do any of the following:  
SKIP  
REPEAT  
to select the  
2. Press  
or  
desired digit.  
CODE/STOP  
3. Press  
to store the selected  
digit. The second digit appears and the  
TAD announces, “second digit”.  
• set the TAD to answer calls  
• listen to your messages  
• record a new OGM  
4. Repeat Steps 2 and 3 to set the second  
and third digits of the security code.  
CODE/STOP  
5. After you press  
to store the  
third digit, TAD announces your security  
code by saying, “Code is ---”.  
• record a memo  
• delete individual or all messages  
• change the security code  
• turn on the room monitor  
CODE/  
To check your security code, press  
STOP  
.
OPERATING THE TAD FROM  
A REMOTE LOCATION  
CHANGING THE REMOTE  
OPERATION SECURITY  
CODE  
1. Dial your phone number. Even if the  
TAD is not set to answer calls, it will  
answer after about 10 rings.  
To use your TAD from a remote telephone,  
you must first enter a 3-digit remote opera-  
tion security code. The security code for your  
TAD is preset to 500. Use the preset code, or  
follow these steps to change it.  
2. After the outgoing message plays and  
the TAD beeps, enter your remote oper-  
ation security code.  
Note:  
If you pause for 8 seconds  
between digits, the TAD hangs up.  
Note:  
Steps 2 and 3 require you to enter  
your digit selection within 8 seconds. Other-  
wise, the TAD beeps once and exits setup.  
Start again at Step 1 if this happens.  
3. Enter the remote command (see  
“Remote Commands” on Page 12).  
4. When you finish, press to end remote  
CODE/STOP  
1. Hold down  
. The display  
access.  
shows the code’s first digit and the TAD  
announces, “first digit.”  
11  
Remote Operation  
 
43-723.fm Page 12 Monday, May 22, 2000 10:26 AM  
REMOTE COMMANDS  
Press  
To  
1
1 1  
2
Replay the current message.  
Replay the previous message.  
Play all or new messages.  
Skip to the next message.  
3
# 3  
4
Change the remote security code. Enter a new 3-digit code.  
Play OGM 1.  
Play OGM 2.  
5
# 4  
Record OGM 1. Enter 0 to finish the recording and the TAD will play the new OGM 1 for  
confirmation.  
# 5  
Record OGM 2. Enter 0 to finish the recording and the TAD will play the new OGM 2 for  
confirmation.  
# 6  
7
Record memo. Enter 0 to finish the recording.  
Delete the current message (during playback).  
# 7  
8
Delete all messages.  
Monitor the room where the TAD is installed for 30 seconds.  
Turn on/off the TAD. If the TAD is on it beeps twice when it answers.  
Stops playback, including incoming messages, memos, and the OGM recording.  
Hang up. The TAD announces, “The machine will now hang up.”  
9
0
Notes:  
mands until the TAD beeps once before you  
hang up.  
If your telephone line has CPC service and  
you hang up while the TAD is playing back  
the messages, it stops playback immediately  
and resets to answer the next call.  
After you enter the correct security code the  
TAD announces your command choices.  
When you enter a remote command, the  
TAD performs the operation immediately.  
If you do not have CPC service and you  
hang up while the TAD is playing back the  
messages, the TAD might not recognize that  
you hung up. If someone calls while the TAD  
continues to play the messages, the caller  
hears a busy signal. We recommend that  
you play all the messages or skip forward  
through the messages using remote com-  
Press to end remote access, otherwise,  
the TAD remains connected for about 1  
minute, then disconnects.  
12  
Remote Operation  
 
43-723.fm Page 13 Monday, May 22, 2000 10:26 AM  
ˆ Troubleshooting  
We do not expect you to have any problems with your TAD, but if you do, try these sugges-  
tions. If the TAD still does not operate properly, take it to you local RadioShack store for assis-  
tance.  
Problem  
Remedy  
The TAD does not answer calls.  
Check all phone line connections.  
Make sure the AC adapter is properly con-  
nected.  
TAD is full. Delete messages.  
TAD is not turned on. Press ON/OFF.  
The outgoing announcement is distorted.  
Re-record the announcement, speaking in a  
normal tone of voice about 8 inches from the  
TAD.  
The TAD does not respond to remote commands.  
Carefully re-enter your remote operation secu-  
rity code. If the TAD fails to respond, the secu-  
rity code might have reset to the default code.  
Enter the default remote security code (500).  
Check for a power outage. Make sure the AC  
power is connected to the wall outlet and the  
9V DC adapter is properly connected to the  
TAD.  
Do not enter commands while the TAD is mak-  
ing announcements or sounding tones.  
• Wipe the TAD with a damp cloth occa-  
sionally to keep it looking new.  
CARE  
To enjoy your TAD for a long time:  
Modifying or tampering with the TAD’s inter-  
nal components can cause a malfunction  
and might invalidate its warranty and void  
your FCC authorization to operate it. If your  
TAD is not performing as it should, take it to  
your local RadioShack store for assistance. If  
the trouble is affecting the telephone lines,  
the phone company can ask you to discon-  
nect your TAD until you have resolved the  
problem.  
• Keep the TAD dry. If it gets wet, wipe it  
dry immediately.  
• Use and store the TAD only in normal  
temperature environments.  
• Handle the TAD gently and carefully. Do  
not drop it.  
• Keep the TAD away from dust and dirt.  
13  
Troubleshooting  
 
43-723.fm Page 14 Monday, May 22, 2000 10:26 AM  
THE FCC WANTS YOU TO  
KNOW  
LIGHTNING  
Your TAD has built-in protection circuits to  
reduce the risk of damage from surges in  
telephone line and power line current. These  
protection circuits meet or exceed the FCC  
requirements. However, lightning striking the  
telephone or power lines can damage your  
TAD.  
In the unlikely event that your TAD causes  
problems on the phone line, the phone com-  
pany can temporarily discontinue your ser-  
vice. If this happens, the phone company  
attempts to notify you in advance. If advance  
notice is not practical, the phone company  
notifies you as soon as possible and advises  
you of your right to file a complaint with the  
FCC.  
Lightning damage is not common. Neverthe-  
less, if you live in an area that has severe  
electrical storms, we suggest that you unplug  
your TAD during storms to reduce the possi-  
bility of damage.  
Also, the phone company can make changes  
to its lines, equipment, operations, or proce-  
dures that could affect the operation of your  
TAD. The telephone company notifies you of  
these changes in advance, so you can take  
the necessary steps to prevent interruption of  
your telephone service.  
14  
Troubleshooting  
 
43-723.fm Page 15 Monday, May 22, 2000 10:26 AM  
ˆ Notes  
15  
Notes  
 
43-723.fm Page 16 Monday, May 22, 2000 10:26 AM  
Limited One-Year Warranty  
This product is warranted by RadioShack against manufacturing defects in material and workman-  
ship under normal use for one (1) year from the date of purchase from RadioShack company-owned  
stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, Ra-  
dioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING  
THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED  
IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED  
HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RE-  
SPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY  
LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFOR-  
MANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, IN-  
CLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS  
OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDEN-  
TAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE  
POSSIBILITY OF SUCH DAMAGES.  
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limita-  
tion of incidental or consequential damages, so the above limitations or exclusions may not apply to  
you.  
In the event of a product defect during the warranty period, take the product and the RadioShack  
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, un-  
less otherwise provided by law: (a) correct the defect by product repair without charge for parts and  
labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase  
price. All replaced parts and products, and products on which a refund is made, become the prop-  
erty of RadioShack. New or reconditioned parts and products may be used in the performance of  
warranty service. Repaired or replaced parts and products are warranted for the remainder of the  
original warranty period. You will be charged for repair or replacement of the product made after the  
expiration of the warranty period.  
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,  
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or  
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs  
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as  
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs  
of product removal, installation, set-up service adjustment or reinstallation.  
This warranty gives you specific legal rights, and you may also have other rights which vary from  
state to state.  
RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102  
12/99  
We Service What We Sell  
A
Cat. No. 43-723  
RadioShack  
A Division of Tandy Corporation  
Fort Worth, Texas 76102  
05A00  
Printed in China  
 

PYLE Audio Speaker PLMRBS10 User Guide
Quatech Switch Serial Device Server User Guide
Radio Shack Answering Machine TAD 1027 User Guide
RCA CRT Television E13319 User Guide
RIDGID Nail Gun R250SFA User Guide
Roberts Gorden Electric Heater EP 100 User Guide
Ryobi Printer 3404DI User Guide
Ryobi Router R181D User Guide
Samsung Computer Monitor 152V User Guide
Samsung Satellite Radio SADPCI 202 User Guide