Peerless Industries TV Mount MIS374A User Manual

Installation and Assembly:  
20" Column Mount  
Model: MIS374A  
Max Load Capacity: 80 lb (36.3 kg)  
3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com  
ISSUED: 03-30-07 SHEET #: 124-9053-1  
 
Installation to Solid Concrete Column  
WARNING  
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.  
• Make sure that the column will safely support the combined load of the equipment and all attached hardware and  
components.  
Make sure that column plate (A) is level, use it as a  
concrete  
surface  
1
1
template to mark four mounting holes. Drill four 1/4"  
(6 mm) dia. holes to a minimum depth of 2-1/2"  
(64 mm). Insert anchors (B) in holes flush with  
column as shown (right). Place column plate over  
anchors and secure with four #14 x 2-1/2" screws  
(C). Level, then tighten all fasteners.  
B
Drill holes and insert anchors (B).  
2
A
B
C
WARNING  
• Tighten screws so that column plate is firmly attached,  
but do not overtighten. Overtightening can damage  
screws, greatly reducing their holding power.  
Place plate (A) over anchors (B) and secure with screws (C).  
3
• Never tighten in excess of 80 in. • lb (9 N.M.).  
WARNING  
• Always attach concrete expansion anchors directly to  
load-bearing concrete.  
• Never attach concrete expansion anchors to concrete  
covered with plaster, drywall, or other finishing mate-  
rial. If mounting to concrete surfaces covered with a  
finishing surface is unavoidable, the finishing surface  
must be counterbored as shown below. Be sure  
concrete anchors do not pull away from concrete  
when tightening screws. If plaster/drywall is thicker  
than 5/8", custom fasteners must be supplied by  
installer.  
B
concrete  
column  
A
C
CORRECT  
INCORRECT  
column  
plate  
concrete  
concrete  
column  
plate  
plaster/  
drywall  
plaster/  
drywall  
ISSUED: 03-30-07 SHEET #: 124-9053-1  
3 of 4  
 
Installation of ST 630 to Column Plate  
Note: Model ST 630 is required for assembly.  
Tilt assembly of ST 630 is required to complete step 2.  
Attach tilt assembly to column plate (A) using two 1/4-20 x 1/2 phillips screws (D), two split washers (F) and two flat  
washers(E).  
2
TILT  
ASSEMBLY  
A
E
F
D
Refer to Attaching Adapter Plate to Flat Panel Screen section of ST 630 instruction manual to complete assembly.  
ISSUED: 03-30-07 SHEET #: 124-9053-1  
4 of 4  
©2007, PeerlessIndustries, Inc. Allrightsreserved.  
Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.  
 

Perle Systems Network Card C 100 XXXXX User Manual
Philips Breast Pump ISIS iQ UNO User Manual
Philips Digital Photo Frame SPF2107 12 User Manual
Philips Portable CD Player AX5003 10 User Manual
Pioneer CD Player DEH P3600MP User Manual
POSIFLEX Business Machines Computer Hardware 16280900030 User Manual
Pride Mobility Wheelchair I NFMANU339 User Manual
Princeton Blower VM 502 User Manual
PYLE Audio Car Video System PLCD19XMR User Manual
PYLE Audio Car Video System PLVW1350IR User Manual